Installation method of various hot and cold water taps
The installation of hot and cold water taps is now the choice of many friends for home decoration, so that we don't have to worry about washing our faces with cold water in the winter, so how to install hot and cold water taps? First, the installation of single hole basin faucet When purchasing a single-handle basin faucet, you should pay attention to the diameter of the water outlet. At present, most of the market is filled with hard pipe. Pay attention to the height of the water pipe. It is best to go down from the basin to about 30. When installing, be sure to choose a special angle valve, the angle valve must be fixed with the hot and cold water pipe of the wall outlet. If there is a distance between the angle valve and the water pipe on the faucet, you need to purchase a special pipe to lengthen the link. Do not use other water pipes to connect, otherwise it will leak and fall off due to large water pressure. If the inlet pipe is too long to exceed the outlet pipe, it is enough to cut it off. Note: Do not bend the water pipe to 90 degrees or more than 90 degrees. When installing the basin to remove water, please don't forget to buy the small interface of the faucet (the faucet is shorted). The water pipes buried in the wall must be flushed before installation. Second, the installation of shower and bathtub faucet If you buy a shower, a bathtub, or a wall-mounted faucet, you need to choose the right height to bury the water pipe. The distance between the hot and cold water pipes is about 20 or more. Rinse the water pipe before installation to avoid damage to the faucet due to hard water. Concealed shower, bath faucet: After purchasing the concealed faucet, the sluice spool should be pre-buried in the wall. The thickness of the bathroom wall should be considered before embedding. If the wall is too thin, the spool will not be buried. The plastic protective cover of the valve plug should not be easily removed when it is buried, so as to prevent the cement and other chores from damaging the valve core when it is buried. In addition, when pre-burying the valve core, you should also pay attention to the up and down and left and right directions of the valve core to avoid the valve core being buried. Third, the installation of thermostat Before installing the thermostatic faucet, first check which side of the water pipe is cold water, which side is hot water, especially the hot and cold water pipes are connected incorrectly, so as not to affect the future work of the faucet. Gas and solar water heaters cannot use thermostatic faucets, mainly because the water pressure is too low. Install the thermostatic faucet and install a hot and cold water filter. Fourth, the installation of single hole kitchen faucet Because the kitchen faucet is used frequently, it is easy to loosen when moving and moving. All the requirements are taken for granted, so the lock nut must be tightened. At present, there are a number of faucets on the building materials market to increase the nut fixing screw, which is super good and stable. The obvious effect will become the trend of a generation. Review Installing hot and cold water taps at home can solve many problems. It is no wonder that so many friends want to know how to install hot and cold water taps. I hope you can understand the installation method of hot and cold water taps introduced in the small series.
Globe Valves and angle valves are designed for throttling or regulating flow in commercial and industrial applications. Bronze, cast iron, or cast ductile iron materials. Threaded, flanged, or solder end connections.
Angle valves for use in commercial and industrial applications. Typical services include hot and cold water, HVAC, steam, compressed air, gas and other general utility services. Angle Valves, Angle Globe Valves, Brass Angle Valve, Zinc Angle Valve ZHEJIANG KINGSIR VALVE CO., LTD. , https://www.kingsir-valve.com
Vacuum angle valve is used for turn on or shut off the airflow in the vacuum pipeline, the applicable media is air and non-corrosive gases.
It has two structures, one is angle type and another is a 3-way type within an ISO-KF or ISO-F various flange end pre-pump port.
a) Small diameter (≤DN50) valve body are precision investment casting.
b) Large diameter (> DN50) valve body are molding shaped seamless steel or steel plate.
c) Bellows sealed structure can withstand 150ºCtemperature, metal sealed structure can withstand 450ºCtemperature.
d) Can install on any position to control the airflow in the vacuum pipeline, as an on-off valve purpose