What is toilet waterproofing practice? What is the waterproof height?

In the decoration part, waterproofing the bathroom is to protect our daily life and prevent the toilet from leaking downstairs. It does not allow water to penetrate the building. Whether it is for our own safety or for the neighbors and the safety of the floors, we must do a waterproof project for the bathroom. As the structure and use of the bathroom determines the complexity and importance of the bathroom waterproofing, how to do a good job of bathroom waterproofing is a matter of great concern to everyone. What is the waterproof height of the bathroom? What is the specific procedure for toilet waterproofing?

First, bathroom waterproof practices

The specific approach is as follows:

1, the ground with cement mortar to the direction of the drain to find the slope, but the surface should be smooth. The slope near the entrance is small, and the slope near the floor drain is large.

2. The pipeline shall be built near the root of the floor and near the floor drain to enhance waterproofing. Pipe root construction sealant seal, cement wipes smooth feet, brush waterproof coating, glass fiber cloth reinforced layer 1 to 2 layers.

3, the wall surface clean and smooth without light dust, small particles, wall ground at the intersection of small original angle or slope angle. When the waterproof paint is applied, the glass cloth is reinforced with 1 to 2 layers.

4, the total thickness of polyurethane waterproof coating requires more than 1.5 mm. Can not rely on the number of times to decide. Root tube, corner reinforcement layer at the first brush, room temperature 4h after the dry, and then a large area brushing, smearing. There must be no leakage or bubbling. After a large area of ​​brushing and curing for 24 hours, brush the next layer.

5, first brushing the facade after the brushing plane, the next time brushing direction and the vertical again. When the film is semi-cured for the last time, the coarse sand is thrown to facilitate the later combination with the cement mortar.

6, the ground waterproof layer should be brushed out of the bathroom door 300mm wide. Waterproof floor waterproof layer should be higher than the ground 200mm.

7. Do 36 hours of closed water test as required.

Second, bathroom waterproof height

Waterproof layer in the wall, column and other parts of the height of flipping (from the room surface to complete above the surface) should not be less than 100mm; high humidity room (such as bathroom) wall or direct water shower wall (such as shower, urinal) The waterproof layer should be done. The waterproof layer should be painted as follows:

1、Install the wall surface with hose shower head and the two sides of the wall surface from above 1800mm;

2. The wall surface of the shower head installed with the concealed pipe (without hose) and its both sides of the wall surface shall not be lower than the shower head height above the ground, and shall not be less than 1800mm;

3, The wall that contacts with the bathtub, from the ground to the top surface of the bathtub is 300mm above;

4. The surface of the wall in contact with the washbasin is 300mm above the wash basin;

5, urinals from above the ground 1800mm;

6, through the floor of the pipe (including casing), from the root of the pipe above 100mm.

Editing summary
About the bathroom waterproof height and bathroom waterproof practices introduced here, bathroom waterproofing is very important for every household, I hope everyone can pay attention to it, so as not to add to their own home decoration unnecessary worry.

Bathroom Renovation Decoration Waterproof Entrance Decoration Cement Glass Coating Interior Decoration Room Glass Door Bathroom Waterproof Practice Toilet Waterproof Bathroom Door Bathroom Leakage

Push Pull Props

Push Pull Props

Pull-push prop are used for supporting the wall and column formwork

There are two kinds of pull-push props. One is suitable for the formwork not higher than 3000mm;

Another is suitable for the formwork higher than 3000mm as a reinforcer

Characteristics:

Highdegree of standardization

Simple site operations

Quick adjustment

Here comes our 5 types of Scaffolding systems:

- Cup lock Scaffolding(C-Lock Scaffolding)

- Ring lock Scaffolding

-Kwistage Scaffolding

-H-frame Scaffolding

-ID15 Scaffolding Tower, this type Scaffolding is the most widely used in construction, such like bridge.

-Whole Aluminum Scaffolding

Push Pull Props,Push Pull Props Adelaide,Push Pull Acrow Props,Adjustable Steel Push-Pull Props

HENGSHUI PIONEER IMP & EXP TRADING CO ., LTD , https://www.hspioneer.com